I've never had a Strat, but am I right in assuming that you would float a two-point Strat Trem in the exact same manner that you would float a Floyd Rose bridge? It seems to be the same principle. What about a vintage-style six-screw Strat trem?
I've never had a Strat, but am I right in assuming that you would float a two-point Strat Trem in the exact same manner that you would float a Floyd Rose bridge? It seems to be the same principle. What about a vintage-style six-screw Strat trem?
Axen: Jackson DK2M, Fender Deluxe Nashville Telecaster, Reverend Warhawk 390, Taylor 914ce, ESP LTD Surveyor-414
Amphen: Jet City JCA22H and JCA12S cab, Carvin X-60 combo, Acoustic B20
Effecten: "Thesis 96" Overdrive/Boost (aka DVM OD2), Hardwire DL-8 Digital Delay/Looper, DigiTech Polara Reverb, DigiTech EX-7 Expression Factory and CF-7 Chorus Factory, Danelectro CF-1 Cool Cat Fuzz
"I wish Imagine Dragons would be stuck in an Arcade Fire for an entire Vampire Weekend."--Brian Posehn
From Fender's website:
Stratocaster guitars can have four distinctive types of bridges. The most well-known bridge is the vintage-style "synchronized" tremolo. The other three are the American Series bridge, which is a modern-day two-pivot bridge; the non-tremolo hardtail bridge; and a locking tremolo, such as the American Deluxe or Floyd RoseĀ® locking tremolos. If you have a non-tremolo "hardtail" bridge, proceed to "Intonation (Roughing it out)."
First, remove the tremolo back cover. Check your tuning. For a vintage-style tremolo bridge, a great way to enhance its performance is to pull the bridge back flush with the body using the tremolo arm. Then loosen all six screws located at the front edge of the bridge plate, raising them so that they all measure approximately 1/16" (1.6 mm) above the top of the bridge plate. Then tighten the two outside screws back down until they're flush with the top of the bridge plate. The bridge will now pivot on the outside screws, leaving the four inside screws in place for bridge stability. For a two-pivot model such as the American Series bridge, use your tremolo arm to pull the bridge back flush with the body and adjust the two pivot screws to the point where the tremolo plate sits entirely flush at the body (not lifted at the front or back of the plate).
Allowing the bridge to float freely (no tension on the tremolo arm) using the claw screws in the tremolo cavity, adjust the bridge to your desired angle—Fender spec is a 1/8" (3.2 mm) gap at rear of bridge. You'll need to retune periodically to get the right balance between the strings and the springs. If you prefer a bridge flush to the body, adjust spring tension to equal string tension, while the bridge rests on the body (you may want to put an extra 1/2 turn to each claw screw to ensure that the bridge remains flush to the body during string bends). Caution: Do not over-tighten the springs, as this can put unnecessary tension on the arm during tremolo use. Finally, you may wish to apply a small dab of ChapstickĀ® or VaselineĀ® at the pivot contact points of the bridge for very smooth operation.
I never throw away things, even bookmarks. Good read @ http://www.premierguitar.com/article...r_Stratocaster
DVM's Ever-Expanding Gear List:
Guitars - W-A-A-A-Y-Y too many to list. Check 'em all out HERE
Amps & Cabs - "Kap'n Kerrang-aroo" BYOC 18W TMB kit amp head; Mojave Coyote head; Fender Hot Rod Deluxe Lacquered Tweed Ltd. Ed.; Allen Sweet Spot kit amp; BYOC Tweed Royal kit amp; Epiphone Valve Jr. combo + mods; Drive 2x12 cab / Celestion G12M Greenback + G12H30; AB Custom Audio 1x12 cab / Celestion Alnico Blue
Pedals/Effects - ZILLIONS, including DVM's Home-built Pedals - See some HERE and HERE, TOO!
DVM's Gear Photos
Visit MY WEBSITE!